Our Work
Chicago HVAC Projects
Real jobs. Real results. Browse a selection of heating and cooling projects we've completed across Chicago, Rockford, and surrounding Illinois communities.
High-Efficiency Furnace Installation
Replaced a 20-year-old single-stage furnace with a 96% AFUE two-stage unit, cutting the homeowner's heating bills by 35%. Full ductwork inspection included.
Central AC Replacement
Installed a 16 SEER2 Carrier central air conditioning system for a 2,400 sq ft vintage greystone. Custom refrigerant line routing to preserve the home's original aesthetic.
Smart Thermostat & Zoning System
Upgraded a three-flat building to a Ecobee zoning system with individual floor controls, enabling each unit to maintain independent temperatures.
Full Ductwork Overhaul
Removed and replaced 40-year-old galvanized ductwork in a 3,000 sq ft home. Redesigned layout improved airflow balance across all six zones by over 50%.
Emergency Furnace Repair
Diagnosed and repaired a failed heat exchanger during a polar vortex event. On-site within 2 hours, system restored same day — family stayed warm through the cold snap.
Annual Maintenance Plan — Multi-Unit
Managing annual tune-ups for a 12-unit apartment building. Preventative care has eliminated emergency calls and extended equipment life across the entire property.
Rheem Condenser Installation
Set a new Rheem condensing unit on a leveled rock pad against a brick wall, with a dedicated disconnect box and proper conduit routing for safe, code-compliant operation.
Aprilaire Whole-Home Humidifier
Installed an Aprilaire humidifier on the furnace plenum with PVC drain piping and an annual maintenance label so the homeowner can keep ideal humidity all winter long.
Flame Sensor Replacement
Diagnosed short-cycling caused by a carbon-fouled flame sensor. Swapped the worn rod for a new one and confirmed proper ignition sequencing before leaving.
Rusted Coil Access Panel Repair
Found a corroded access panel and dirty A-coil during a cooling check. Replaced the panel, cleaned the coil, and restored airflow for reliable summer performance.
Burnt Contactor Repair
Traced an intermittent cooling failure to a charred contactor wire. Replaced the contactor and damaged wiring to eliminate the heat damage and restore reliable operation.
Condenser Fan & Motor Service
Removed the top panel to inspect the fan blade and motor assembly on a rooftop unit. Lubricated and tested components before reassembly for smooth, quiet operation.
Cracked Heat Exchanger Replacement
Identified visible cracks and rust at the heat exchanger bends during a safety inspection. Recommended and completed a full replacement to eliminate any carbon monoxide risk.
Evaporator Coil Deep Clean
Tackled a heavily soiled evaporator coil packed with lint and dust. Applied foaming coil cleaner, flushed the fins, and restored airflow and cooling efficiency.
New System Serial Tag
Documented the serial number and model data on a newly installed system for warranty registration and future service records.
Condensate Drain Line Install
Fitted a new PVC condensate line fitting through the unit casing and sealed the penetration to prevent leaks and protect the surrounding structure.
Condenser Fan Motor Replacement
Removed a failed outdoor condenser fan motor and installed a replacement, wiring it to the existing harness and confirming smooth fan operation before reassembly.
Rooftop Condenser Coil Cleaning
Opened a rooftop condenser and applied Nu-Brite coil cleaner through the fins, flushing out debris to restore heat-transfer efficiency and lower operating pressures.
Capacitor & Contactor Replacement
Replaced a failing dual run capacitor and pitted contactor in a condenser control box to resolve a no-cool call and protect the compressor from further damage.
Dual Rheem Condenser Install
Set two Rheem condensers on a concrete pad beside a brick wall, ran copper lines through a filter drier, and completed electrical and start-up testing for both systems.
Corroded Drain Pan Replacement
Found a rusted condensate pan with standing water and sludge. Replaced the pan and cleared the drain line to stop leaks and prevent secondary water damage.
Blower Motor Deep Clean
Removed a heavy mat of dust and pet hair from a furnace blower motor to restore airflow, reduce strain on the motor, and improve indoor air quality.
Damaged Condensate Fitting Repair
Repaired a cracked and broken condensate fitting in a condenser panel, clearing debris and resealing the connection to stop the leak.
Furnace Blower Assembly Replacement
Swapped out a worn furnace blower motor and squirrel-cage assembly, re-mounting it to the bracket and confirming quiet, balanced operation after reinstallation.
Condenser Fan Motor Swap
Compared the old, rusted condenser fan motor against its replacement on the rooftop, then installed the new motor and fan blade to restore cooling airflow.
Condenser Compressor Inspection
Opened a condenser to inspect the compressor, refrigerant lines, and coil assembly, verifying clearances and connections for safe, efficient operation.
Bryant Attic Furnace Install
Installed a Bryant furnace in a tight attic crawlspace, routing flue and combustion air through the structure while maintaining required clearances to combustibles.
Rheem Gas Furnace Installation
Set a Rheem gas furnace with PVC condensate and combustion piping, a yellow-handled gas shut-off, and armored electrical supply, then ran full start-up and safety checks.
Furnace with Aprilaire Humidifier
Paired a Rheem furnace with an Aprilaire whole-home humidifier on the supply plenum, running copper feed tubing and a flue vent for balanced winter humidity.
Dual Run Capacitor Replacement
Swapped a failed dual run capacitor (30/5 MFD) for a new one to restore proper fan and compressor operation on a no-cool service call.
Clogged Condensate Line Clear-Out
Found a stained, slow condensate line with standing water at the clean-out tee. Flowed the line and cleared buildup to stop the overflow backup.
Furnace Cabinet Leak Repair
Diagnosed rust-colored water pooling inside a furnace cabinet from a condensate leak. Repaired the source and cleaned out the chassis to prevent further corrosion.
High-Efficiency Furnace Service
Opened an EnergyGuide-rated furnace to diagnose a gas valve and inducer motor issue, confirming safe ignition and proper venting before the heating season.
Failed Heat Exchanger Removal
Removed a heavily rusted heat exchanger assembly showing corrosion at the base, then prepped the furnace for a full replacement to eliminate any carbon monoxide risk.
Blower Housing Component Repair
Replaced a damaged section of blower motor housing and re-secured wiring to restore proper blower operation and airflow through the system.
Borescope Coil Inspection
Used a TESLONG borescope to inspect deep inside an evaporator coil for hidden debris and corrosion, documenting condition without full disassembly.
Flame Sensor Replacement
Swapped a carbon-fouled flame sensor for a new one to restore reliable ignition sequencing and eliminate intermittent furnace lockouts.
Rooftop Condenser with Disconnect
Installed a rooftop condenser on a wooden pad with a dedicated electrical disconnect box mounted to the cinder block wall, running conduit and insulated refrigerant lines.
Ruptured Capacitor Replacement
Found a blown GE dual run capacitor (35/5 MFD) with a ruptured top and corroded terminals. Replaced it to restore fan and compressor operation.
Rooftop Filter Replacement
Swapped pleated 14x20x2 filters in a rooftop unit cabinet, inspecting the coil rack and foil-faced insulation while confirming proper airflow back to the building.
Frozen Evaporator Coil Thaw
Diagnosed a heavily iced-over evaporator coil with restricted airflow. Thawed the A-coil, cleared the condensate PVC, and corrected the underlying low-airflow cause.
Rheem Furnace with PVC Flue
Set a Rheem gas furnace elevated on blocks with PVC combustion and condensate venting, a black iron gas supply, and full start-up and safety checks.
Corroded A-Coil Removal
Removed a heavily rusted A-coil evaporator with a stained drain pan and corroded copper fins, prepping the system for a clean replacement coil.
Hot Surface Igniter Replacement
Replaced a failed hot surface igniter to restore proper furnace ignition, confirming correct amperage draw with a clamp meter before reassembly.
Dual Rheem Water Heater Install
Installed two Rheem Professional gas water heaters side-by-side with copper piping, flue venting, foam insulation, and gas controls commissioned and leak-tested.
Lennox Rooftop Unit Service
Serviced a commercial Lennox packaged rooftop unit on a metal roof, inspecting the electrical disconnect, copper line sets, and intake hoods with the panel open for diagnostics.
Flame Sensor Replacement
Replaced a corroded, oxidized flame sensor rod to restore reliable ignition and prevent repeated furnace lockouts during the heating season.
Inducer Motor Housing Repair
Reseated and re-secured an inducer motor housing assembly, reconnecting the red, green, yellow, and brown wiring harness to restore proper draft induction.
Aprilaire 700 Series Humidifier Install
Mounted an Aprilaire 700 Series whole-home humidifier to the galvanized supply duct with PVC drain piping, a dedicated humidistat, and low-voltage wiring.
Trane XE 1000 Refrigerant Charge
Serviced a row of four Trane XE 1000 condensers, connecting a digital manifold gauge set and refrigerant cylinder to diagnose and recharge the open unit.
Rooftop Condenser Coil Inspection
Opened a rooftop condenser fan assembly to inspect the coil fins for dirt streaking and airflow restrictions, documenting condition for a cleaning recommendation.
Cracked Cabinet Panel Repair
Diagnosed a jagged fracture in a furnace cabinet panel that was allowing air leakage, sealing and reinforcing the metal to restore proper airflow and cabinet integrity.
Corroded Contactor Replacement
Replaced a heavily rusted contactor with a pitted, corroded screw terminal and frayed wiring to restore safe, reliable compressor control.
Clogged Drain Port Clean-Out
Disconnected the rubber condensate elbow to expose a sludge-filled drain port, cleared the blockage, and reinstalled the hose with a fresh clamp.
Attic Rheem Furnace Install
Installed a high-efficiency Rheem furnace in an attic on an overflow drain pan, routing PVC intake and exhaust and a gas line with an inline shut-off.
Rheem Furnace with Gas Line Set
Set a Rheem furnace with a black iron gas pipe union, a junction-box disconnect, and a filter drier on the copper refrigeration lines, then ran start-up checks.
Failed Heat Exchanger — Burner Side
Removed a rusted heat exchanger assembly showing corroded fins and soot-stained burner intakes, prepping the furnace for a full replacement to eliminate CO risk.
Blower Wheel & Control Board Service
Serviced a furnace blower assembly in an attic, inspecting the orange blower wheel, control board wiring harness, and a rusted cabinet plate for replacement.
Debris-Filled Condenser Coil Clean
Cleared a condenser coil packed with matted debris and leaves around the red shut-off valve, restoring airflow and protecting the compressor from overheating.
Furnace & Water Heater Closet Install
Installed a Rheem furnace with an Aprilaire humidifier and PVC venting alongside a Rheem Performance water heater labeled for the second floor, with copper and gas lines commissioned.
Serving All of Chicagoland
From Lincoln Park to Oak Park, Evanston to Orland Park, and across Rockford and surrounding communities — our certified technicians cover all of Northern Illinois for residential and light-commercial HVAC needs.
View All Services →Don't Let a Broken System
Ruin Your Comfort
Chicago and Rockford weather doesn't wait — and neither should you. Get a free quote from our certified HVAC technicians today.
Get Your Free Quote →